All G.R.A.S. microphone preamplifiers are based on a small ceramic thick-film substrate with a very high input impedance. The ceramic substrate is shielded by a guard ring to minimize the influence of stray capacitance and microphonic interference.The casing is made of stainless steel for maximum strength and durability. This preamplifier ensures reliable operation even under humid conditions owing to the heat generated by internal power dissipation.
G.R.A.S. 26AC can handle both single and dual-sided power supplies. The supply can vary between 28 VDC and 120 VDC single-sided or ±14 VDC and ±60 VDC dual-sided. When using the high supply voltage (120 VDC or ±60 VDC), the dynamic range exceeds 140 dB.
The electrical circuit in G.R.A.S. 26AC is built on a ceramic substrate using selected low-noise components to gain very low self-noise. The electrical self-noise is so low that system noise is mainly determined by the microphone cartridge’s thermal noise.
The low-frequency cut-off of the G.R.A.S. 26AC preamplifier is mainly determined by the input impedance of the preamplifier and the capacitance of the microphone cartridge (see a graph in the Specifications. The capacities 20 pF,6.5 pF and 3 pF equal the typical capacitances of 1/2", 1/4"" and 1/8" microphone cartridges respectively. The high-frequency cut-off is determined by the preamplifier’s ability to drive capacitive loads (slew rate), caused by the cable. For large-signals, the effects of these parameters must be accounted for when measurements are performed. A graph in the Specifications shows the large-signal response for G.R.A.S. 26AC for various capacitive loads corresponding to different cable lengths. The output level is in decibels relative to 1 Volt. Typical capacitance for the cable is 100pF/m (30pF/foot).
The G.R.A.S. 26AC 1/4" Preamplifier is provided with a 3 m lightweight cable terminating in a 7-pin LEMO series 1B plug. The cable is only 2.5 mm in diameter and will withstand temperatures from -40 oC to +150 oC. An adaptor (GR0010) for G.R.A.S. 1/2" microphones is included.
7-pin LEMO plug 1B male (ext. view)
Typical applications and use
- The 26AC-CL is identical to 26AC except that you can specify the wanted cable length (in cm).
- The 26AC-1 is identical to 26AC except that it is provided with an integrated 5-pin LEMO connector and is provided with a built-in TEDS-chip.
|Frequency range (±0.2 dB) with 18 pF microphone dummy||Hz||2.5 to 200 k|
|Input impedance||GΩ // pF||20 // 0.4|
|Output Voltage Swing, max. @ ±14V/+28V power supply||Vp||12|
|Output Voltage Swing, max. @ ±60V/+120V power supply||Vp||50|
|Noise (A-Weighted) max.||µV||2.5|
|Noise (A-Weighted) typ.||µV||1.8|
|Noise (Linear 20 Hz – 20 kHz) max.||µV||6|
|Noise (Linear 20 Hz – 20 kHz) typ.||µV||3.5|
|Power supply, single||V||28 to 120|
|Power supply, balanced||V||±14 to ±60|
|DC-offset, min., single suppy||V||0.5 x Vs - 1|
|DC-offset, max., single suppy||V||0.5 x Vs + 4|
|DC-offset, balanced supply||V||-1 to 4|
|Temperature range, operation||°C / °F||-30 to 70 / -22 to 158|
|Temperature range, storage||°C / °F||-40 to 85 / -40 to 185|
|Humidity range non condensing||% RH||0 to 95|
|Connector type||7-pin LEMO (FGG.1B.307)|
|CE/RoHS compliant/WEEE registered||Yes / Yes, Yes|
|Weight||g / oz||8.0 / 0.28|
|Weight with cable and connector||g / oz||50.0 / 1.76|
Conditions: 23 °C Ambient temperature, ±60V/+120V power supply, 18 pF dummy microphone, 3 m output cable.
Typical frequency response for 1/2" (20 pF), 1/4" (6.5 pF) and 1/8" (3 pF) microphones
Typical max RMS output signal with 120 V and 30 V supply
G.R.A.S. Sound & Vibration reserves the right to change specifications and accessories without notice.
Adapter for 1/4" preamplifier and 1/2" microphone
3 m LEMO 7-pin - LEMO 7-pin Cable
Customized Length LEMO 7-pin - LEMO 7-pin Cable
1/4" Microphone Holder, POM
1/4" Microphone Holder, Stainless Steel
Adapter for 1/8" microphone and 1/4" preamplifier
Right-angled (90º) Adapter for 1/4" Microphone and 1/4" Preamplifier
6pF Preamplifier-input adapter for 1/4" microphones
2-Channel Power Module with gain, filters and SysCheck generator
2-Channel Universal Power Module with signal conditioning and PC interface