Typical applications and use
- For use in confined spaces
- High frequency measurements
- High pressure measurements
- Sound intensity measurements
- Near-field measurements
- Anechoic boxes
- Hearing-aid measurements
- Wide frequency range
- Low noise level
- Very small dimensions
- 4-pin LEMO 00 connnector
All G.R.A.S. microphone preamplifiers are based on a small ceramic thick-film substrate with avery high input impedance. The ceramic substrate is shielded by a guard ring to minimise the influence of stray capacitance and microphonic interference. The casing is made of stainless steel for maximum strength and durability. The small dimensions of this preamplifier ensures reliable operation under humid conditions owing to the heat generated by internal power dissipation.
G.R.A.S. 26AR can handle both single and dual-sided power supplies. The supply can vary between 28 VDC and 120 VDC single-sided or ±14VDC and ±60 VDC dual-sided. When using the high supply voltage (120VDCor ±60VDC), the dynamic range exceeds140 dB.
The electrical circuit in G.R.A.S. 26AR is built on a ceramic substrate using selected low-noise components to gain very low self-noise. The electrical self-noise is so low that system noise is mainly determined by the microphone capsule’s thermal noise.
The low-frequency cut-off of the G.R.A.S. 26AR preamplifier is mainly determined by the input impedance of the preamplifier and the capacitance of the microphone capsule. The capacities 20 pF,6.4 pF and 3 pF equal the typical capacitances of 1/2", 1/4" and 1/8" microphone cartridges respectively.
The high-frequency cut-off is determined by the preamplifier’s ability to drive capacitive loads (slewrate), caused by the cable. For large-signals, the effects of these parameters must be accounted for when measurements are performed. The large-signal response for G.R.A.S. 26AR for various capacitive loads corresponding to different cable lengths is shown in the data sheet. The output level is in decibels relative to 1 Volt. Typical capacitance for the cable is 100pF/m (30pF/foot).
G.R.A.S. 26AR is to be connected with a 3m light-weight cable (AA0057). Its 4-pin LEMO plug connects to the preamplifier and its 7-pin LEMO to a power module. The cable is only 2.5 mm in diameter and will withstand temperatures from -40 oC to +150 oC. An adapter GR0010 for G.R.A.S. 1/2" microphones is included.
Ext. view of 4-pin LEMO plug 00 male and 7-pin LEMO plug 1B male (ext. view)
|Frequency range (±0.2 dB) with 18 pF microphone dummy||Hz||2.5 to 200 k|
|Input impedance||GΩ // pF||20 // 0.4|
|Output Voltage Swing, max. @ ±14V/+28V power supply||Vp||10|
|Output Voltage Swing, max. @ ±60V/+120V power supply||Vp||50|
|Noise (A-Weighted) max.||µV||6|
|Noise (A-Weighted) typ.||µV||4|
|Noise (Linear 20 Hz – 20 kHz) max.||µV||10|
|Noise (Linear 20 Hz – 20 kHz) typ.||µV||8|
|High-pass filter @3dB cut-off||Hz||TBD|
|Power supply, single||V||28 to 120|
|Power supply, balanced||V||±14 to ±60|
|DC-offset, min., single suppy||V||0.5 x Vs - 1|
|DC-offset, max., single suppy||V||0.5 x Vs + 4|
|DC-offset, balanced supply||V||-1.5 to 5|
|Temperature range, operation||°C / °F||-30 to 70 / -22 to 158|
|Temperature range, storage||°C / °F||-40 to 85 / -40 to 185|
|Humidity range non condensing||% RH||0 to 95|
|Connector type||4-pin LEMO (FGG.00.304)|
|CE/RoHS compliant/WEEE registered||Yes / Yes, Yes|
|Weight||g / oz||4.0 / 0.14|
Conditions: 23 °C Ambient temperature, ±60V/+120V power supply, 18 pF dummy microphone, 3 m output cable.
Typical low-frequency response of Type 26AL for ½″ (20 pF), ¼″ (6.5 pF) and ⅛″ (3 pF) microphones
Typical max. rms output signal with 120 V and 30 V supplyG.R.A.S. Sound & Vibration reserves the right to change specifications and accessories without notice.
Adapter for 1/4" preamplifier and 1/2" microphone
3 m LEMO 00 4-pin - LEMO 7-pin Cable for 26AR
Customized Length LEMO 7-pin - LEMO 7-pin Cable
1/4" Microphone Holder, POM
1/4" Microphone Holder, Stainless Steel
Adapter for 1/8" microphone and 1/4" preamplifier
Right-angled (90º) Adapter for 1/4" Microphone and 1/4" Preamplifier
6pF Preamplifier-input adapter for 1/4" microphones
2-Channel Power Module with gain, filters and SysCheck generator
2-Channel Universal Power Module with signal conditioning and PC interface
G.R.A.S. Sound & Vibration reserves the right to change specifications and accessories without notice.