GRAS 40LS 1/4" CCP Precision Surface Microphone

Freq range: 5 Hz to 70 kHz
Dyn range: 46 dB(A) to 167 dB
Sensitivity: 1.8 mV/Pa

Technology

Typical applications and use

  • Automotive industry
  • Wind-induced noise measurement on vehicles
  • Outdoor measurements on testing grounds
  • Wind-tunnel testing

Design

Just 2.5 mm thick, the 40LS has an integrated CCP preamplifier and is delivered with a built-in TEDS chip, which enables it to be programmed as a complete unit.

The 40LS requires a constant-current power supply, such as the GRAS 12AL CCP Supply, or any other CCP compatible power supply.

Close manufacturing tolerances together with the advantages of the TEDS chip, provide the 40LS with a high degree of interchangeability; a major advantage which excludes accounting for individual characteristics.

The 40LS is both very stable and robust. It has an integrated 1.5 m co-axial cable with a microdot connector and is delivered with a supple detachable silicon-rubber fairing.

Because of its lightness, the microphone with fairing can readily be mounted on surfaces using double-sided adhesive tape.

All GRAS microphones are individually checked and calibrated before leaving the factory.

An individual calibration chart is supplied with each microphone.

Calibration

When leaving the factory, all GRAS microphones have been calibrated in a controlled laboratory environment using traceable calibration equipment. Depending on the use, measurement environment and internal quality control programs we recommend that the microphone is recalibrated at least once a year.

We offer two kinds of calibration as an optional after-sales service: GRAS Traceable Calibration and GRAS Accredited Calibration.

GRAS Traceable Calibration is a traceable calibration performed by trained personnel under controlled conditions according to established procedures and standards. This is identical to the rigorous calibration that all GRAS microphones are subjected to as an integral part of our quality assurance.

GRAS Accredited Calibration is performed by the GRAS Accredited Calibration Laboratory that has been accredited in accordance with ISO 17025 by DANAK, the Danish Accreditation Fund.

If you want a new microphone set delivered with an accredited calibration in stead of the default factory calibration, specify this when ordering.

Learn more at gras/calib.

Quality and warranty

GRAS microphone sets are made of components from our proven standard portfolio and are all manufactured of high-quality material and branded parts that were chosen and processed to ensure life-long stability and robustness.

All parts are manufactured and assembled at the factory in Denmark by skilled and dedicated operators in a verified clean-room environment. The microphone diaphragm, body and unique protection grid are made of high-grade stainless steel and make the microphone set resistant to physical damage as well as corrosion caused by aggressive air or gasses.

This, together with the enforced gold-plated microphone terminal guarantees a highly reliable connection. Thanks to the high quality, our warranty against defective materials and workmanship is 5 years.

Service

Should you by mistake damage the diaphragm on a GRAS microphone we will in most cases be able to exchange it at a very reasonable cost and short turn-around time. This not only protects your investment but also meets your quality assurance department since you do not have to worry about new serial numbers etc.

Specifications

Frequency range (±1 dB)
Hz
10 to 20 k
Frequency range (±3 dB)
Hz
5 to 70 k
Dynamic range lower limit (microphone thermal noise)
dB(A)
< 46
Dynamic range upper limit with GRAS CCP preamplifier
dB
167
Set sensitivity @ 250 Hz (±2 dB)
mV/Pa
1.8
Power supply (Constant Current Power)
mA
2 to 20
Microphone venting
Front
Output impedance
Ω
<50
Temperature range, operation
°C / °F
–55 to 100 / -67 to 212
Temperature range, storage
°C / °F
-40 to 85 / -40 to 185
TEDS UTID (IEEE 1451.4)
27 v. 1.0
Connector type
Microdot 10/32
CE/RoHS compliant/WEEE registered
Yes / Yes / Yes
Weight
g / oz
3 / 0.101
Specification Conditions

Typical frequency response

GRAS Sound & Vibration reserves the right to change specifications and accessories without notice.

Dimensions

Ordering info

Included items

GRAS GR0933

Adhesive tape, pre-cut, single-sided

GRAS GR0934

Adhesive tape, pre-cut, double-sided

GRAS MI0031

Cleaning tissue

GRAS AE0046

Adapter, BNC male to Microdot female

GRAS GR1252

Silicon-rubber fairing

 Optional

GRAS 12AQ

Power Module (2-ch.)

GRAS RA0202

Calibration Adapter (required)

GRAS 42AP

Intelligent Pistonphone with built-inprecision barometer (250 Hz or 251.2 Hz,114 dB ±0.05 dB) (recommended)

GRAS 42AA

Pistonphone (250 Hz, 114 dB ±0.08 dB)

GRAS GR1297

Stainless-steel fairing

GRAS CA0029

Traceable Calibration of Microphone Set

GRAS CA2301

 Accredited Calibration of Microphone Set

GRAS Sound & Vibration reserves the right to change specifications and accessories without notice.

Get Quote